db9
Advanced Member-
Content Count
71 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Gallery
Articles
Member Map
Garage Directory
Classifieds
Everything posted by db9
-
cheers craig, this one is stamped with ford logo but carnt find part no though two pedals are stamped ford 73bb i assume a late one then ? btw, i got some more brake shoes coming lol fingers crossed be right ones
-
hi, cortina mk3 , is the pedal box same on pfl,fl models ?
-
Toothed Locking washers for rear low Atlas radius arms
db9 replied to Rschofield's topic in Suspension, Steering, & Brakes
no prob glad you sorted some -
Toothed Locking washers for rear low Atlas radius arms
db9 replied to Rschofield's topic in Suspension, Steering, & Brakes
HI rscofield I have couple of sets these if ya still after some -
hi all anyone know torque for pinion nut mk4 v6 axle? big 27mm one , Haynes mk3 book says 71-86 ft lbs, had torque wrench on mine and hit 90 ft lbs already any tips/advice be great thanks
-
hi all im after info on mustang arch trims for mk3 anyone know who posted on the topic, or link to it I carnt find it anywhere lol
-
HI andy yes tis me 👍
-
im near swadlincote south derbyshire
-
sorry ken, not mean to hijack your thread lol got some old pics if you want em
-
-
is close to finish line lol just needs vynil roof, screens, bespoke exhaust, few odds/ends
-
good to see it getting on
-
is this my old one ? MLR
-
yes did that, im bout half way just need courage to pop last bit in lol
-
hi craig, thankyou swapped master cyl for scabby old one, and bled brakes, all seems good my n.o.s. one, I pulled apart, not stuck and no rust, very clean inside can only assume it was sucking air in through res rubbers ? have fitted new seals now but how hell you get res back in lol what a pig, dare not put too much pressure on it fear of cracking it any tips/advice ? thanks again
-
hi all, help lol mk3 tina Ev8, having probs bleeding new brake system servo is my original mk3, I think, just cleaned/painted, master cylinder is n.o.s later mk4/5 ? I think, 3 outlet type( girling 746) are these not compatible together ? prob seems to be around this area as not getting any fluid into pipes, tried bleeding it with mate and one man kit too, it just blows air out and sucks fluid back up have removed master cyl and tested on bench, blasts fluid out all 3 holes, so it not stuck/seized the later master cyl is longer, maybe only works with mk4/5 servo ? any help/advise
-
cheers for reply rt have got some coming from eeebay
-
hi all Cortina mk3 76 E what is correct size caliper bolts ? I am fitting 2.8 vented discs/calipers and the original bolts are wee bit on the short size, have seen longer ones on fleabay but for escorts/capri 7/16 unf
-
hi all I am getting ready to fit new vynil roof ,mk3 2.0E what is best glue to use and how much is needed ? CHEERS
-
wow top job
-
hi henry ford factory look, I like that thankyou :showoff: as pete,craig said early cars had loom under rad with fuel pipe held on with plastic clips, later cars loom goes through rad side panels big 3" rbr grommets re lower rad panel, think all mk3 had the 3 round hole type as on my 76 E, you can use square type with bit of fetling I have pics if you need them
-
I said the same Richard :icecream: c,mon Emily get a thread going looks like awesome resto :winner: more pics please :showoff: