Jump to content

107me

Advanced Member
  • Content Count

    56
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by 107me

  1. Thanks guys got eBay eyes on.👀 but looking for std struts with spring seats at fair price👍 Lotus out my price range🤪
  2. Hi looking for a pair of struts for refurb.😊
  3. Ok so I’ve now bought a car with one of these on🙈
  4. Or alternatively anyone who would lend me one to get 3D scanned😊
  5. Hi looking for one of these with or without Rev counter, any condition inc damaged👍
  6. 107me

    1500 pxflow parts

    Hi sorry I had 3 but all gone😞
  7. Think I have one but need to find it.👍 if someone else beats me to it no problem😊
  8. It’s the pfl one I need. (Passenger side) is it the template or a repair section you have? Would you sell it if a section pic would be great👍
  9. Hi I’m looking for the bottom section of the front chassis leg pass side PFL. mines rotted out similar to attached pic. anyone got a good front section they would part with🤪 thanks mark
  10. Great got a pair of mk4 coming👍
  11. Looking for similar info but other way round will mk4/5 inner wing (upper inner only not leg ) fit pre face lift mk3? thanks
  12. Just found answer in an old post. All sorted👍
  13. Hi been wrestling with stripping my PFL dash out.🤔 cant seem to find a way to release the dash top pad.🙈 I don’t have a manual to hand and I can’t find anything by searching. basically I’ve got the vents and clocks out. Can see spring clips on front edge but for the life of me can’t get them to release. must be me, but if anyone has a technique would appreciate if you could advise as the pad is mint and I don’t want to damage anything😩 thanks in advance mark
  14. Yes thanks for your efforts👍 I had seen them on eBay, but based on cost, I wanted to see if anyone had anything in their parts bin they would sell/swop first😁
  15. as Title- to get my speedo working I’m told I need an 8t worm gear and a 24t speedo gear. if you have anything or could tell me which cars used these gears that would be great. also I have a 23t speedo gear in excellent nick and 7t worm gear to swop or sell if that helps thanks mark
  16. It’s a cortina 2.3 axle with the larger 72mm bearings rather than the usual 67mm ones. its going on my taunus coupe 👍
  17. Looking for a pair of back plates any condition to suit 72mm bearing atlas axle thanks mark
  18. Do you have a mig welder? if so put a washer over the stud and weld on full power. then weld a nut on top of the washer by filling the threaded hole on full power let it go dull and remove stud with socket heat releases stud, never had one not work for me👍
  19. Meant to say 2.9 xr4x4 used a 2 bolt starter that’s fits Capri 🤪 but not 2.8😩
  20. Thanks for the reply. i have a Granada and a Capri bell housings (cast iron) and a Sierra xr4x4 alloy bell housing. the granny and Capri are both 2 bolt and the 2 bolt starter has different centres so won’t bolt up to alloy bell housing off Sierra 2.8 xr4x4 i know all variants of 4x4 ie Dohc / cos etc use 3 bolt starters but are you saying they would work on the cologne with a Capri 2.8 flywheel? i don’t have any 3 bolt starters to check. thanks mark
  21. Hi anybody got one of these knocking about? wanted for my taunus coupe / cologne v6 type 9 swop using alloy bell housing. also after the back plate for 3 bolt starter as well😁 thanks mark
  22. Try 73tina he’s breaking a pfl and has axle &dash for sure. hes got an add in the for sale section 👍
  23. That price is for a pair so not as bad as it first looks😩 not cheap buy not bad (if you can fit them yourself) if you consider what’s gone into making them.
×
×
  • Create New...