markbagelboy
-
Content Count
471 -
Joined
-
Last visited
Everything posted by markbagelboy
-
yes, when throbnozzle racing built my engine & skimmed my head he shortened my push rods 977, 1200, 1300, pre-xflow engines, I would have thought used the same pushrods
-
-
Hi Tay14 I have a early mk2 Cortina and I sent my legs of to gaz shocks as you can no longer get the inserts for the early series1 cars I told gaz I was running 2inch lower springs. they said they will put a shorter stroke in the shock so my springs will not fall out when jacking car up, cost is £85 per leg mark
-
http://www.burtonpower.com/clutch-cover-7-5-flat-fingers-190mm-fp260c.html this is the correct pressure plate & you must use spacer with it from burton
-
that pic is the type of pressure plate with the rounded thrush bearing that you need that pic from burton is for the 1.1 1.3 so yes you are right mark
-
-
check to see what rotor arm you've got in your dizzy top one is for motorcraft dizzy bottom one for lucas dizzy
-
well i have had a eye test done and they say i need reading classes B)
-
you will need to measure you diff flange to see what one you're got as there are 3 different sizes The 86mm & 92mm are on the early cars Anglias Cortinas and MkI Escorts, the 109mm is on the MkII and is the same size as Atlas.
-
i had a look on Accuspark web site it looks like they do not do electronic ignition for Motorcraft distributor, but will do a lucas distributor with electronic ign fitted for the prexflow for £64.95
-
http://www.aldonauto.co.uk/shop/product.asp?strParents=&CAT_ID=39&P_ID=92 Aldon do one for Motorcraft distributor OR lucas distributor which ever one your running mark
-
Hi mate this photo should help you, mark
-
threads are correct for mk2 cortina 7/16 with 12mm shank
-
http://rover.ebay.com/rover/1/710-53481-19255-0/1?ff3=4&pub=5574629005&toolid=10001&campid=5335900709&customid=&mpre=http://www.ebay.co.uk/itm/M16-CALIPER-BOLTS-MK1-MK2-MK3-CAPRI-ESCORT-CORTINA-RS2000-MEXICO-2-0S-280-2-8I-/200964798670?hash=item2eca6f78ce:g:3QYAAOSwd4tUCL31
-
Mk2 cortina lowering spring - where from?
markbagelboy replied to v5uk's topic in Suspension, Steering, & Brakes
http://stores.ebay.co.uk/DaveSimsAutomotive?_trksid=p2047675.l2563 This guy sells them Mark -
Hi ed The express steel panel wheel well follows the contour of the bottom of rear 1/4 panel Is your wheel well a home made 1 You could make your own fillet Mark
-
http://www.autosparks.co.uk/index.php?content_page=42
-
Inside the back of tacko you have a calibration dial which you can Adjust via the instrument light holder. Which you have to remove With a small screw driver adjust dial .you can use a Strobe light with a tacko reader would help To confirm correct revs Mark
-
Mine
-
bolts are 3/8 unf but I can't remember how long they are just measure the old ones for length
-
East Kent Trim windscreen rubber which mk2 best fit
markbagelboy replied to H Cortina's topic in Bodywork & Paint
I got my door, boot, & rear window rubbers from http://rover.ebay.com/rover/1/710-53481-19255-0/1?ff3=4&pub=5574629005&toolid=10001&campid=5335900709&customid=&mpre=http://www.ebay.co.uk/usr/rotary_products_new_old_car_company And they fitted perfectly -
http://www.speedycables.com/index.html
-
NGK BP6ES FOR GT
-
Hi m8 Northampton motor sport come highly recommended http://www.northamptonmotorsport.com/?id=16
-
0.625in is correct one for you m8