swcortina 38 Posted December 29, 2019 (edited) 18mm front anti roll bar with chassis brackets £40 NOW SOLD. Estate rear hinge and torsion bars set up £20 Pair of mk3/4/5 rear lower arms (from mk3) £20 12mm rear anti roll bar £20Various behind dash heater/air flow pipes from fl mk3 Pair front hubs £70Pair new rubber front lower arm bushes £10 1600 rear axle £120 (collection only) 1600 gearbox £80 (collection only) Pair front springs £20 Pair rear springs £20 All plus postage unless collection only. Edited January 2, 2020 by swcortina Quote Share this post Link to post Share on other sites
Kencrackfixer 31 Posted January 1, 2020 Hi Do you have the bolts and spacers for the anti roll bar ? Quote Share this post Link to post Share on other sites
swcortina 38 Posted January 2, 2020 19 hours ago, Kencrackfixer said: Hi Do you have the bolts and spacers for the anti roll bar ? Front or rear arb? Quote Share this post Link to post Share on other sites
Kencrackfixer 31 Posted January 3, 2020 Front The bolts that attach to the lower arm Quote Share this post Link to post Share on other sites
sheffieldcortinacentre 529 Posted January 3, 2020 Do you need a full kit or everything except the bushes Think I can help either way. Quote Share this post Link to post Share on other sites
dgo 66 Posted January 3, 2020 51 minutes ago, Kencrackfixer said: Front The bolts that attach to the lower arm The ones like this? Linky Quote Share this post Link to post Share on other sites
swcortina 38 Posted January 3, 2020 1 hour ago, Kencrackfixer said: Front The bolts that attach to the lower arm Got some used bolts with washers and spacing tubes, no bushes. Quote Share this post Link to post Share on other sites
Kencrackfixer 31 Posted January 4, 2020 Thanks The linky thing did the trick Quote Share this post Link to post Share on other sites
swcortina 38 Posted January 5, 2020 (edited) Mk3 steering column £40 plus p&p Now sold Edited February 11, 2020 by swcortina Quote Share this post Link to post Share on other sites
swcortina 38 Posted January 11, 2020 Axle provisionary sold Quote Share this post Link to post Share on other sites
swcortina 38 Posted January 13, 2020 (edited) 1600 pinto gearbox, some bell housing bolt holes damaged £60 Edited January 13, 2020 by swcortina Quote Share this post Link to post Share on other sites
Kencrackfixer 31 Posted January 15, 2020 On 1/4/2020 at 7:58 PM, Kencrackfixer said: Thanks The linky thing did the trick I spoke too soon ! When they turned up ,not as thick as the originals. So still after the bolts and washers if available cheers ken Quote Share this post Link to post Share on other sites
RT 1006 137 Posted January 15, 2020 1 hour ago, Kencrackfixer said: I spoke too soon ! When they turned up ,not as thick as the originals. So still after the bolts and washers if available cheers ken Those reproduction/aftermarket bolts are just a standard M8 bolt. The original bolts were a type of shoulder bolt with a standard M8 thread and 13mm AF head but with a fatter main body than a normal bolt. The original spacers and washers had a larger inside diameter to accommodate the shoulder bolt which is why if you use them with the aftermarket bolts then the spacers and washers don't fit snugly to the bolt. Sounds like you're looking to source originals but they're going to be difficult to find as even any cars being broken for parts are likely to have had these link bolts replaced at some point in their lives and probably with the narrower bolts. Quote Share this post Link to post Share on other sites
swcortina 38 Posted January 16, 2020 14 hours ago, Kencrackfixer said: I spoke too soon ! When they turned up ,not as thick as the originals. So still after the bolts and washers if available cheers ken I'll dig you out a set Ken. Quote Share this post Link to post Share on other sites
swcortina 38 Posted January 16, 2020 (edited) Mk3 GT/GXL centre console gauges, one has a small burn hole in the bulb holder. £25 Edited January 16, 2020 by swcortina Quote Share this post Link to post Share on other sites